HOLLEY 4150 750 CFM Questions - Corvette Forum : DigitalCorvettes.com Corvette Forums
 
 
Go Back   Corvette Forum : DigitalCorvettes.com Corvette Forums > C3 Corvette Forums > C3 Corvette
Register Forums Garage Garage Mark Forums Read Auto EscrowInsurance Advertise

Notices

C3 Corvette
C3 Corvette General | Technical | Performance | Aftermarket | Discussions

Other sections:
Corvettes Classifieds
Corvette Detailing & Car Care
Corvette Audio/Video/Radar
General Automotive/Shop/Tools
Corvette Performance Driving/Racing

( Sponsored by: Zip Corvette Parts )

Shops/Tuners
Custom Image Corvettes
A&A Corvette
Corvette tuner

Interior
Corvette aftermarket products

Insurance



Parts & Products
Race Ramps
Edelbrock
ATI/Procharger
Corvetteguys.com
Melrose Motorsports
Parts Taxi
Airaid
Pfadt Racing
Madvette Motorsports
Hi-tech Custom Concepts
Corvette Garage
Corvette Parts and Accessories
Corvette Car Care Products
Corvette HID

Tracks/Schools
Bob Bondurant School of High Performance Driving
Corvette driving school

Wheels/Tires
Cray Wheels

Services
BADWERKS.com
Reply
 
Thread Tools
Old 10-19-2019, 02:33 PM   #1
DeeVeeEight
DC Crew
 
DeeVeeEight's Avatar
 
Posts: 879
Member #60406
Member since: May 2007
Location: South NJ

My Corvette(s)
1979 L-82 5 Speed

Thanks: 0
Thanked 0 Times in 0 Posts
HOLLEY 4150 750 CFM Questions

Holley 4150 tuning questions. I rebuilt the carburetor last week. During disassembly I found that the secondary power valve has a plug installed. My primary jets are 71's and the secondaries are 80's (mechanical secondaries). After rebuilding and tuning I found that the idle mixture screws have an uneven effect on the vacuum reading (max vacuum is approximately 15 inches). Is this because the jets are so rich? The engine runs smooth at idle and is fairly smooth in response throughout the range, though there is a slight hesitation when opening up the secondaries - which I am hoping to fine tune and eliminate. Your thoughts? The engine is a fresh 355 with a mild cam, 9 to 1 compression.
DeeVeeEight is offline   Reply w/quote Quick reply to this message
if you don't ask, you get the same answer as no.
Sponsored Links
Advertisement
 
Old 10-19-2019, 05:22 PM   #2
autowiz
DC Crew
 
autowiz's Avatar
 
Posts: 4,685
Member #149514
Member since: Nov 2014
Location: Pompano Beach, Fl USA

My Corvette(s)
2000 silver/black

Thanks: 307
Thanked 364 Times in 319 Posts
My thoughts on the subject are 750cfm might be a lot for the 355 with a mild cam. No? Wouldn't a 650 be better suited for a near stock c3 motor? When we oversize or undersize the carb for the engine we are using we find ourselves with these idle issues because the airflow requirements and the placement of passages on either side of the throttle plates for the idle circuit is in a fixed location and can not be changed with re jetting. I think 750 would be a good carb for a 396 or a 427. A big block. You cant treat the carb like it is fuel injection. There is no idle air control motor or valve here. That is decided by the flow rate stamped on the carb.

If you want performance you should consider a Speed Demon Carb. They are owned by Holley. Just a higher tier of carb than your Holley. But you will still do better with the 650 for all around drivability. Alternatively you could consider an aftermarket fuel system like the FAST easy efi 2.0 that comes with a throttle body that flows 1150cfm but it can still hold a great idle with even a 4 cylinder engine because of the precise control from the GM stepper motor regulating airflow for the idle circuit(IAC).
autowiz is offline   Reply w/quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Corvette Forum : DigitalCorvettes.com Corvette Forums forums, you must first register.
Please enter your desired user name (12 CHARACTERS MAXIMUM), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
City / State / Country?
Where you live
What kind of Corvette(s) do you own?
This field is not required.
Insurance
Please select your insurance company (Optional)

Log-in


Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Powered by vBadvanced CMPS v3.2.2

All times are GMT -6. The time now is 03:07 PM.




Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
2003-2011, DigitalCorvettes.com - All Rights Reserved