Joined
·
3,603 Posts
How do you pull the electrical harness out of the back of the mirror? I'm trying to install my new invisicord and can't see where to plug the wires in with the harness still in the mirror. Thanks.
Removing Electrical Harness on Mirror
1 - 9 of 9 Posts
Joined
·
1,643 Posts
If I remember correctly, it just pulls right out. But im sure you got it by now.
Joined
·
3,603 Posts
Well I stopped trying when it didn't come out easily. There is like a little button thing on it and the only things I could really get a hold of were the wires and I didn't want to pull them out of their connections by accident. I'll try again tomorrow.
Joined
·
16,115 Posts
I will get you some pics from the service manual shortly:thumbsup:
:cheers:
:cheers:
Joined
·
3,603 Posts
Thanks!
Joined
·
386 Posts
TreCool626
You have a C6 Corvette, so the motor must be running while this procedure is being done.The mirror wiring harness is rectangular shaped. On the upper edge there is a tab that must be pinched down firmly, and held down, while you pull the harness out by the wires. I stress the "firmly" because it's in tight, and must be pinched down hard, and held down, to release the harness. After its out, turn it around so you can see the wires. Insert the "green" wire of your invisicord just "above" the black wire in the harness. Insert the "red" wire of your invisicord just "below" the "center" pink wire in the harness. (There are 2 pink wires in the harness, use the one in the "center" of the harness.) Insert the blades from the invisicord "strongly" so they stay put. Your done! Snap the harness back in the mirror, and be on your way. It's really easy, even though it seems like this...:thumbsup:
![]()
You have a C6 Corvette, so the motor must be running while this procedure is being done.The mirror wiring harness is rectangular shaped. On the upper edge there is a tab that must be pinched down firmly, and held down, while you pull the harness out by the wires. I stress the "firmly" because it's in tight, and must be pinched down hard, and held down, to release the harness. After its out, turn it around so you can see the wires. Insert the "green" wire of your invisicord just "above" the black wire in the harness. Insert the "red" wire of your invisicord just "below" the "center" pink wire in the harness. (There are 2 pink wires in the harness, use the one in the "center" of the harness.) Insert the blades from the invisicord "strongly" so they stay put. Your done! Snap the harness back in the mirror, and be on your way. It's really easy, even though it seems like this...:thumbsup:
Joined
·
3,603 Posts
Thanks a bunch guys! I'll probably do that on Friday when I have time. I was concerned that pulling on the wires may disconnect them from the harness. I'm excited to get that sucker going. I'll let you know what I think when I've completed it. Thanks again, John.
Joined
·
108 Posts
TreCool626
You have a C6 Corvette, so the motor must be running while this procedure is being done.The mirror wiring harness is rectangular shaped. On the upper edge there is a tab that must be pinched down firmly, and held down, while you pull the harness out by the wires. I stress the "firmly" because it's in tight, and must be pinched down hard, and held down, to release the harness. After its out, turn it around so you can see the wires. Insert the "green" wire of your invisicord just "above" the black wire in the harness. Insert the "red" wire of your invisicord just "below" the "center" pink wire in the harness. (There are 2 pink wires in the harness, use the one in the "center" of the harness.) Insert the blades from the invisicord "strongly" so they stay put. Your done! Snap the harness back in the mirror, and be on your way. It's really easy, even though it seems like this...:thumbsup:
![]()
I have 3 pink wires in my mirror, any suggestions which is the 'hot'?
I have actually tried them all and no power to the Val.
EDIT:
The orange wire was 'hot' so im set thanks for the info
1 - 9 of 9 Posts
