Corvette Forum : DigitalCorvettes.com Corvette Forums banner

1 - 13 of 13 Posts

·
El Teafive
Joined
·
10,489 Posts
Discussion Starter #1
Finishing up where we left off on Sunday..

Lower ball joints
One Upper Ball joint.. (other one was replaced)

Lowering kit
Front Spring

Anyone want to Stop By Brakes Plus (294 and Golf) on Sunday is more then welcome.

Patrick, What alignment specs did you use for your car?


then at some point I need to:
-Install my 6 channel amp
-swap the rear 6x9's for a 6.5" woofer, a tweeter and either a 5.25" or 4" midrange
-Figure out how to relocate the front speakers and then install my 96 door panels
 

·
Registered
Joined
·
3,027 Posts
I'd love to stop by, but I maybe doing some work on the Jeep. The previous owner installed security lugnuts ON EVERY WHEEL STUD!!:spanked:

A fellow Jeeper is going to help me remove all 20 lugnuts so I can put on some better tires then the POS tires on it now.
 

·
DC Crew
Joined
·
53,209 Posts
ragvette said:
What time are you going to be at the shop? :partyon:
I'll see you on Sunday. As for alignment specs, I'll see if I can dig them up. They are right between the standard alignment and an auto-cross setup.

They have to be here somewhere.....
 

·
Registered
Joined
·
104 Posts
ragvette said:
What time are you going to be at the shop? :partyon:
Should be there around 9:30am like Jeff said.
Hey Ragvette will you bring the ZO6?
I love the EB ZO6,i just gotta get one of those next to the ZR-1.
I have a friends '01 ZO6 on my lift right now doing a clutch and trans on it.
 

·
DC Crew
Joined
·
53,209 Posts
ZR1Pete said:
Should be there around 9:30am like Jeff said.
Hey Ragvette will you bring the ZO6?
I love the EB ZO6,i just gotta get one of those next to the ZR-1.
I have a friends '01 ZO6 on my lift right now doing a clutch and trans on it.
I stopped by about 1:30p (I was driving around) and no one was there. It was nice out so I didn't mind .. ..

:partyon:
 

·
El Teafive
Joined
·
10,489 Posts
Discussion Starter #9
Patrick96LT4 said:
I stopped by about 1:30p (I was driving around) and no one was there. It was nice out so I didn't mind .. ..

:partyon:
Did you set your clock ahead???

Al, Pete, an I were there until around 2pm, then left for a bit to eat..

Don and Rodney stopped by Earlier..

So my best guess is your clock was an hour behind since we had to change them last night :D

On the plus side the car is done, front spring needs to settle a bit and I need an Alignment.
 

·
Registered
Joined
·
6,158 Posts
ZR1Pete said:
Should be there around 9:30am like Jeff said.
Hey Ragvette will you bring the ZO6?
I love the EB ZO6,i just gotta get one of those next to the ZR-1.
I have a friends '01 ZO6 on my lift right now doing a clutch and trans on it.
ZR1Pete,
It was great catching you guys at the shop this morning. DAM, I was really impressed on all of your knowledge. Yourself, Jeff and if I'm not mistaken Al? (sorry if I didn't get it right) really know your ****. :thumbsup:

:cheers:
 

·
DC Crew
Joined
·
53,209 Posts
-=Jeff=- said:
Did you set your clock ahead???

Al, Pete, an I were there until around 2pm, then left for a bit to eat..

Don and Rodney stopped by Earlier..

So my best guess is your clock was an hour behind since we had to change them last night :D

On the plus side the car is done, front spring needs to settle a bit and I need an Alignment.
Yea, maybe it was later then. No biggie, I went for a drive and figured if you were there, that's cool, if not I had a nice drive!
 

·
Supporting Vendor
Joined
·
152 Posts
Quote:

ZR1Pete,
It was great catching you guys at the shop this morning. DAM, I was really impressed on all of your knowledge. Yourself, Jeff and if I'm not mistaken Al? (sorry if I didn't get it right) really know your ****.



Hey Rodney,Don it was nice of you guys to stop by the shop.
You guys are welcome to stop by anytime.



:cheers: :partyon:
 
1 - 13 of 13 Posts
Top